Happy Easter
VITA UPDATER 1.0.0.4
NEW SOFTWARE FOR VITA OPERATING TABLE
We inform you that a new software for Vita operating table has been released. Thanks to VITA UPDATER version 1.0.0.4 it will be possible to set some important parameters, please follow the operating instructions below before updating the system.
#Have a look to the operating instructions.
You can download the software VITA UPDATER 1.0.0.4 going to the softwares’ section or by clicking on the button below.
IMPORTANT NOTE (15/05/18)
THE NEW SOFTWARE IS NOW VITA UPDATER 1.05
VITA FIRMWARE DSP 1.08
A NEW FIRMWARE IS AVAILABLE
The firmware version DSP 1.08 will improve the table’s characteristics. Infact, thanks to this new firmware release, the table will have the floor and table’s anticollision protection and the possibility to set the recognition* of some sections installed on the tabletop. Furthermore it improves the angles degrees reading between the operating table and the display remote control.
* The sections’recognition function can be activated only by display remote controls having firmware version RCD 1.8 or higher.
#Have a look to the operating instructions.
You can download the new firmware DSP 1.08 directly on the softwares’ section or by clicking on the button below.
– Please be informed that OPT Surgisystems will be closed on Monday 2nd of April for “Pasquetta”, which is a public holiday in Italy.
New Software Key
Dear partners,
We inform that the new software key for VANTO CAT, ASSO CAT and CENTURY CAT is available. The current software key for VANTO, ASSO and CENTURY technical softwares will expire during July 2018.
In order to continue using the technical softwares it will be necessary to download the new software key into OPT.cat's section Documentation/Softwares or by clicking on this link.
The software key is valid for VANTO CAT, ASSO CAT and CENTURY CAT softwares, however, it will be necessaty to install it into every single software to make it run.
Happy holidays
SUMMER CLOSURE 2018
Dear partners, we inform that OPT Surgisystems will be closed from Monday 6th of August to Friday 24th of August 2017 for the usual summer break.
During the summer closure OPT Customer Service will only provide technical assistance for urgent matters.
We kindly advise you to place all urgent spare parts orders before the summer closure, as during that period the spare parts orders will NOT be dispatched.
If you wish to contact us, please use the email address customerservice@opt-ita.com or call us to the following mobile number +39 345 6580 484.
OPT Customer Service wishes you happy holidays !
Christmas Closure
Happy Holidays
Dear Partners,
We inform that OPT Customer Service will be closed for Christmas Holidays from the 24th of December to the 6th of January included.
Should you need to contact us for urgent technical support and spare parts orders you can do it by phone or email:
We wish you happy holidays!
OPT Customer Service Team
Firmwares & Softwares Key
VANTO DSP 3.5v - HMI 2.2m
A FIRMWARE SOLUTION FOR 8811000 TABLETOP
We inform you that a new firmware for VANTO operating tables has been released.
The firmware DSP version 3.5v solves a problem with tabletop model 8811000
With tabletop model 8811000 by activating the longitudinal movement and reaching the limit (towards head or legs section) an error “software extralimit – movements blocked” could
appear in some particular conditions.
You can download the firmware version DSP 3.5v – HMI 2.2m from the softwares’ section or by clicking on the button.
CENTURY DSP 2.07
A NEW FIRMWARE FOR CENTURY OPERATING TABLE
Furthermore a new firmware version for Century operating table has been released.
It is firmware DSP 2.07 that solves a problem that could occur during the operating system pickup.
With column Century Plus 8703000 and longitudinal trolley 8790000 (having height variation) during the operating system pickup the base of the column could, in some cases, collide with the trolley’s pump.
You can download the new version DSP 2.07 and the release notes directly on the softwares’ section or by clicking on the button below.
NEW SOFTWARES KEY
SOFTWARES VANTO CAT, ASSO CAT & CENTURY CAT
The new software key for VANTO CAT, ASSO CAT and CENTURY CAT is now available.
The current version is going to expire on the 15th of January 2019, so don’t forget to download it before it is too late!
You can download the new SOFTWARE KEY from the softwares’ section or by clicking on the button below.
New Operating Instructions
OI_AS-S1
ASSO FIRMWARE UPDATE
A new version (Rev1) has been released. The operating instruction shows how to update the firmware on ASSO operating table.
OI_AS-B7
PILOT VALVE INSTALLATION
How to install the pilot valve with a single pressure switch on ASSO operating table.
OI_AS-U6
HYDRAULIC CIRCUIT PURGE
A new version (Rev1) is avalaible. The operating instruction explains how to perform the hydraulic circuit purge on ASSO operating table.
OI_401-B1
STABILIZER MECHANISM UPGRADE
How to upgrade the stabilizer control mechanism on OPT 40/1 operating table.
OI_401-U1
HYDRAULIC CIRCUIT PURGE
How to perform the hydraulic circuit purge on OPT 40/1 operating table.
Vanto Firmware & Software
VANTO DSP 3.6e - HMI 3.0p
THE FIRMWARE FOR VANTO REMOTE CONTROLS WITH DISPLAY
We would like to inform you that a new firmware for Vanto operating tables has been released. The firmware DSP 3.6e – HMI 3.0p will handle the bluetooth communication for Vanto remote control with display code 8800425.
This firmware is compatible with all IR Vanto remote controls from previous versions.
You can download the firmware version DSP 3.6e – HMI 3.0p from the softwares’ section or by clicking on the button.
VANTO CAT 3.5.2
THE NEWEST SOFTWARE VANTO CAT IS AVAILABLE
Together with the new firmware version a new software VANTO CAT has been released.
As for the firmware, the version 3.5.2 will handle the Bluetooth communication for Vanto remote control with display code 8800425.
You can download the new version VANTO CAT 3.5.2 and the release notes directly on the softwares’ section or by clicking on the button below.
New Firmwares & Softwares
ASSO DSP 1.10
NEW ASSO FIRMWARE RELEASE
We would like to inform that a new firmware for Asso operating tables has been released.
Firmware DSP 1.10 will allow to modify the parameter that handles the activation of the electrovalves with the motor pump start.
The value of the parameter to be set is 0.3 and it must be set through the diagnostic software
ASSO CAT version >= 2.8.0 into the table settings menu.
Download version DSP 1.10 from the softwares’ section or with the following button.
ASSO CAT 2.8.0
THE NEWEST SOFTWARE ASSO CAT IS AVAILABLE
Together with the new firmware a new software ASSO CAT has been released.
With the software version 2.8.0 it will be possible to modify the parameter that handles the activation of the electrovalves with the motor pump start.
Get ASSO CAT 2.8.0 and the release notes directly on the softwares’ section or by clicking on the button below.
VITA DSP 1.09
NEW FIRMWARE FOR VITA OPERATING TABLE
Regarding Vita operating tables it is now available a new firmware, release DSP 1.09.
Thanks to this new firmware release will be possible to activate the table movements in the JOG mode. The JOG movements run slower, they exclude the MIN/MAX firmware limits and give the possibility to reach the MIN/MAX mechanical limits.
Download the firmware version DSP 1.09 from the softwares’ section or by clicking on the button.
VITA UPDATER 1.06
PARAMETERS CONFIGURATOR 1.06 FOR VITA OPERATING TABLES
Even a new software version for Vita operating tables is now available.
In the last Vita Updater version new settings parameters have been added: stabilizer pins time, wheels time and upload v.109.
You can get the new version VITA UPDATER 1.0.6 and the related release notes directly on the softwares’ section or through the button below.
Happy summer
SUMMER CLOSURE 2019
Dear partners, we inform that OPT Surgisystems will be closed from Monday 5th of August to Friday 23rd of August 2019 for the usual summer break.
During the summer closure OPT Customer Service will only provide technical assistance for urgent matters.
We kindly recommend placing all urgent spare parts orders within Tuesday 6th of August; after this date all spare parts orders will NOT be dispatched until OPT Surgisystems will reopen.
If you wish to contact us, please use the email address customerservice@opt-ita.com or call us to the following mobile number +39 344 187 09 58 .
OPT Customer Service wishes you happy summer holidays !
Winter Closure
Happy Holidays
Dear Partners,
We inform that OPT Customer Service will be closed for Christmas Holidays from the 21st of December to the 6th of January included.
Should you need to contact us for urgent technical support and spare parts orders you can do it by phone or email:
We take this opportunity to inform that the new software key for VANTO CAT, ASSO CAT and CENTURY CAT is now available. The current version is going to expire on the 15th of January 2020, so don’t forget to download the new version before it is too late!
As usual, the file will be available in the software section of opt.cat.
We wish you happy holidays!
OPT Customer Service Department
New Firmwares & Softwares
INFORMATION
We would like to inform you that since 2020 to all release notes regarding new firmwares will contain a level of priority based on the importance of the update that should be performed on the table. Furthermore, we would like to remind you to read always the release notes which are included in the firmware and softwares folders as they contain important information.
ASSO DSP 1.11
NEW ASSO FIRMWARE RELEASE
We would like to inform that a new firmware for Asso operating tables has been released.
Firmware DSP 1.11 improves the communication between the controls without display with the operating table.
Download version DSP 1.11 from the softwares’ section or with the following button.
VANTO II CPU 2.2
NEW FIRMWARE FOR VANTO II OPERATING TABLE
For Vanto II operating table there is a new firmware available, release CPU 2.2.
This firmware brings new features and improvements about the traction device movements, the batteries status and the joystick for vascular surgery tabletops.
Download the firmware version CPU 2.2 from the softwares’ section or by clicking on the button.
PSU CONFIG 1.10
POWER SUPPLY CONFIGURATOR 1.10 FOR VANTO II OPERATING TABLE
A new version of software PSU Config 1.10 for Vanto II operating table is available.
In this last software version it will be possible to control the anti-handling feature, to select the type of column and to enable/disable the different movements’ speeds.
You can get the new version PSU Config 1.10 and the related release notes directly on the softwares’ section or through the button below.
Firmware for Vanto II
VANTO II CPU 2.3
NEW FIRMWARE FOR VANTO II OPERATING TABLE
A new firmware has been released for Vanto II operating table, it is the release CPU 2.3.
This new firmware improves the collision limits for some accessories. Furthermore the automatic transfer function has been improved.
Download the firmware version CPU 2.3 from the softwares’ section or by clicking on the button.
